Название
#
Заметки
Купить
Bearing Set - Main
00-13 Thrust washers included.
Bearing Set - Rod
00-13 Standard OD.
Bearing Set - Rod
00-13 0.002" oversized OD.
Camshaft - Stock
00-07 "N,P". RH. Except "J" HO.
Camshaft - Stock
00-07 "N,P". LH. Except "J" HO.
Connecting Rod - Stock
00-07 Reconditioned. Press fit pins. Sintered. Ex. HO. W/bearing tang notches.
Std. bearing OD.
Crank Kit - Reman
00-08 "N". Includes bearings. Forging # 53020683. Use old reluctor ring from
original crank. Check for proper physical match before installation.
Cylinder Head - Bare
00-07 "N,P". LH. Except HO. New bare head without valves or springs. With or
without EGR. .2752" guide ID. Valve head diameter 1.917 / 1.457".
Cylinder Head - Bare
00-07 "N,P". RH. Except HO. New bare head without valves or springs. .2752"
guide ID. Valve head diameter 1.917 / 1.457".
Cylinder Head - Complete
00-07 "N,P". LH. Except HO. Reman. Without EGR. Includes valves, springs,
camshaft & lifters. All new valve seats.
Cylinder Head - Complete
00-07 "N,P". RH. Except HO. Reman. Includes valves, springs, camshaft & lifters.
All new valve seats.
Cylinder Sleeve
00-13 3/32 x 3.661 x 5.0625"
Expansion Plug Kit
00-12 Steel plugs.
Expansion Plug Kit
00-12 Brass plugs.
Gasket - Cylinder Head
00-13 MLS. Use new head bolts. Two required.
Gasket - Exhaust
00-07 Exhaust manifold set.
Gasket - Intake
00-07 Intake manifold set.
Gasket - Timing Cover Set
00-02 1st. design.
Gasket - Valve Cover
00-03 Valve cover gasket set. With grommets.
Gasket Set - Full
00-03 MLS head gaskets. Includes "offset lip" front crank seal. Oil pan gasket not
included use OCR287. Use new head bolts.
Gasket Set - Head
00-03 MLS head gaskets. Use new head bolts.
Gasket Set - Lower
00-13 Oil pan gasket not included use OCR287.
Gasket Set - PER
00-03 MLS head gaskets. Includes oil pan gasket. Rebuilder set without rear main or
valve stem seals. Use new head bolts.
Head Bolt Set
00-13 Two sets required. Contains (10) long TTA bolts. The (4) short bolts are not
TTA and can be reused.
Head Spacer Shim
00-13 0.020" thick. Install on block side. Use sealer between shim and block.
(1 per pack).
Oil Pump
00-13 Enginetech "Pressure King" value line pump.
Piston And Ring Kit
00-07 "N,P". Ex. HO. Flat top. 1.252" CH. Fits press or floating rods. Coated skirt.
Kit contains (1) piston with premium rings.
Piston Ring Set
00-07 Premium. Steel or ductile top. 1.5 / 1.5 / 3.0mm.
Piston Set
00-07 "N,P". Ex. HO. Flat top. 1.252" CH. Coated skirt. Fits press or floating rods.
Use S93138 rings.
Rocker Arm
00-13 Int. & Exh. Roller follower. (4 pack).
Timing Chain Tensioner
00-13 Center. Metal plate with 2 chain guides.
Timing Set
00-02 Engines with silent type upper chains only. With early JTEC cam target wheel.
Cam wheel has one "timing window" near the "L" timing mark.
Timing Set
00-08 Without sprockets. Engines with silent type upper chains only. Fits JTEC &
NGC.
Valve - Exhaust
00-07 .2720" stem. 1.457" head. Ex. HO. 21-4N. 0.427" TTG.
Valve - Exhaust
00-07 .2720" stem. 1.457" head. Ex. HO. 21-4N. 0.427" TTG. (25 / bulk).
Valve - Intake
00-07 .2734" stem. 1.917" head. .372" TTG.
Valve - Intake
00-07 .2734" stem. 1.917" head. (25 / bulk).
Valve Guides
00-07 Int. & Exh. .2752 x .4720 x 1.422". Plain ID. Iron. (4 pack).
Valve Lifter
00-07 Hydraulic. Lash adjuster. (4 pack).
Valve Lifter
00-07 Hydraulic. Lash adjuster. (16 pack).
Valve Lifter
00-07 Hydraulic. Lash adjuster. (241 / tray).
Valve Seal - OE Type
00-07 Viton. (20 pack).
Valve Seal - OE Type
00-07 Viton. (100 pack).
Valve Seat
00-12 Intake. 1.690/1.765T x 2.0042 x .2420". 45 Deg. Hi-Chrome cast. (4 pack).
Valve Seat
00-12 Exhaust. 1.203/1.266T x 1.5042 x .2800". 45 Deg. Hi-Chrome Cast. (4 pack).
Valve Spring
00-07 Int. & Exh. 1.935" Free Ht. Conical. (4 pack).
